|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
| OzECruisers General Discussions E/N/D vehicles General Discussion ONLY. NO TECH THREADS |
 |
|
|
Thread Tools | Display Modes |
28-04-2005, 09:44 AM
|
#1 | ||
|
FF.Com.Au Hardcore
Join Date: Dec 2004
Location: Sth East Melb
Posts: 2,357
|
Hey... I broke the little woodgrain strip on the passenger rear door. (EL GHIA)
 : I was trying to fit a large box on the back seat, and managed to catch the woodgrain panel on it, and snap most of the little tabs that hold it in place. Looking at it further.. it appears that i cant swap this for a new one? Do i have to take the door trim off? Or am i going to get reemed here, and have to buy an entire door trim ? John, sunny? Have any lying around ?  : Ash, can you turn away for a minute ? Steve |
||
|
|
|
28-04-2005, 10:34 AM
|
#2 | ||
|
Low and Loud
Join Date: Dec 2004
Location: Melbourne
Posts: 3,273
|
So you have broken the small metal Tabs off the woodgrain piece? If so they are replaceable. I think you can buy them from bunnings. To replace them, you must remove the door trim, insert new metal Tabs into woodgrain, then fit the woodgrain piece, bend them back around the trim, and thats it
 If the woodgrain strip is broken itself, they are replaceable and ive seen a few wreckers here and there who have had them. BTW love the Thread Title :P
__________________
1993 Ford Fairlane NC3 Silver - LTD mockup, Worked V8 & Auto, Fully Optioned, Half of my Audio department at work installed in the car 1993 Ford Falcon XR6 Poly Green Stationwagon - 4.0 I6, Auto, 3:45LSD, All the usual XR6 Stuff but in a wagon  :
|
||
|
|
|
|
28-04-2005, 11:57 AM
|
#3 | ||
|
they call me Tibbo
Join Date: Dec 2004
Location: Brisbane
Posts: 6,163
|
If you haven't damaged the trim itself just sicaflex it back into the right place.. You never have a need to take them off anyway so abit of silicon won't hurt it.. Use the one for aquariums, it has no corrosive properties.
__________________
|
||
|
|
|
|
28-04-2005, 12:04 PM
|
#4 | ||
|
hibernating
Join Date: Dec 2004
Posts: 2,135
|
superglue? :-p
|
||
|
|
|
|
28-04-2005, 12:08 PM
|
#5 | ||
|
not here much anymore
Join Date: Dec 2004
Location: Sthn NSW
Posts: 22,918
|
90% sure you can buy just the trims from Ford if thats what you want to do, but i think they are around $300 each (yes i am talking per bit of 'wood'), thats your typical Ford pricing.
Depending on the damage i'd probably do as has been suggested and just glue ti back on. Or take them all off and have them redone in brushed aluminium or CF finish  _2: .
__________________
2024 F150 XLT
|
||
|
|
|
|
28-04-2005, 07:38 PM
|
#6 | ||
|
Banned
Join Date: Dec 2004
Posts: 4,078
|
LMAO @ thread title.
I would have said glue or something. |
||
|
|
|
|
28-04-2005, 08:52 PM
|
#7 | ||
|
windsor user
Join Date: Dec 2004
Location: Geelong
Posts: 13,123
|
dont use glue, it wont work..
use sikaflex or similar. i have to do the same thing to my woodgrain trims... lol too lazy |
||
|
|
|
|
| Thread Tools | |
| Display Modes | |
|
|
Ah Crap, I broke my woody
Linear Mode
