|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
| OzECruisers General Discussions E/N/D vehicles General Discussion ONLY. NO TECH THREADS |
 |
|
|
Thread Tools | Display Modes |
01-12-2005, 08:48 PM
|
#1 | ||
|
Does Steve have a car?
Join Date: Jan 2005
Location: Melbourne
Posts: 1,566
|
Last few days have been dedicated to cleaning up the engine, which included painting her and replacing all the seals that i could. Now i've ripped the timing case off and decided to change the timing guides as they were broken and worn.
I tried not to move any of the gears but the auxilary gear has slightly moved and now i need to know if i aligned the gears back up properly. Now the engine is at TDC, inlet valve #2 and exhaust valve #3 are open, mark on the cam gear is parallel to the head on inlet side of the engine and the crank gear and auxilary gear marks are aligned to each other. Is this correct?? Need to know asap... Thanx in advance 
__________________
AKA Mr Silver Chasing reliability....  :"When Chuck Norris jumps into water, he does not get wet, the water gets Chuck Norris..."
|
||
|
|
|
01-12-2005, 09:14 PM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Aug 2005
Location: Northern Tablelands
Posts: 940
|
sounds about right
__________________
2000 AU Wagon |
||
|
|
|
|
01-12-2005, 09:53 PM
|
#3 | ||
|
Last warning
Join Date: Dec 2004
Location: Mornington Peninsula, Victoria HeadCount: 3
Posts: 11,194
|
the cam gear mark is actually meant to be 3 degrees or 3mm above the level of the head, but i'd imagine with various changes to the engine (head skim, headgasket) the mark could be a tad off either way.
and yes the marks on the aux shaft and crank should be pointed at each other.
__________________
FALCN6 - Turbo, Air Bag Suspension - Hibernating EL GT - Supercharged NASCAR - 83 Thunderbird , Bagged DAILY - BA Fairlane Ghia, Boss 260 Turbo OFFROADER - Ford Explorer 
|
||
|
|
|
|
01-12-2005, 10:44 PM
|
#4 | ||
|
FF.Com.Au Hardcore
Join Date: Aug 2005
Location: Northern Tablelands
Posts: 940
|
well not really,,that is the allowable,it is meant to be as level as possible with the top of the head but can be up to 3mm above,so lond as it's sitting any where in between level and 3mm above it's ok.
__________________
2000 AU Wagon |
||
|
|
|
|
01-12-2005, 10:59 PM
|
#5 | ||
|
Last warning
Join Date: Dec 2004
Location: Mornington Peninsula, Victoria HeadCount: 3
Posts: 11,194
|
actually factory specification is the 3mm above, all the allignment information i used is from the factory workshop manual.
__________________
FALCN6 - Turbo, Air Bag Suspension - Hibernating EL GT - Supercharged NASCAR - 83 Thunderbird , Bagged DAILY - BA Fairlane Ghia, Boss 260 Turbo OFFROADER - Ford Explorer
|
||
|
|
|
|
02-12-2005, 05:53 AM
|
#6 | ||
|
Does Steve have a car?
Join Date: Jan 2005
Location: Melbourne
Posts: 1,566
|
Either way, if i were to move the cam gear another tooth, it will be about 6mm above the line, so i'm guessing i got it pretty much spot on. Thanx guys, some progress pics should be coming very shortly
__________________
AKA Mr Silver Chasing reliability.... :"When Chuck Norris jumps into water, he does not get wet, the water gets Chuck Norris..."
|
||
|
|
|
Timing gear alignment...
Linear Mode
